Difference between revisions of "Splitflaps"

From Whitespace (Hackerspace Gent)
Jump to: navigation, search
 
(13 intermediate revisions by 2 users not shown)
Line 1: Line 1:
 
{{Project
 
{{Project
 
|Current=Yes
 
|Current=Yes
 +
|Participants=Merlijn.
 +
Thijs, Bert C, Michael
 
|Short description=twitter feed gets displayed on 4x40 splitflaps
 
|Short description=twitter feed gets displayed on 4x40 splitflaps
 
}}
 
}}
 +
STOCK SUBPAGE http://www.0x20.be/Splitflaps/stock
 +
 +
https://github.com/galgalesh/Splitflaps
 +
http://splitflaps.wordpress.com/
 +
 +
http://www.0x20.be/Project_Flappers
 +
 
Microcontroller: Netduino chip.
 
Microcontroller: Netduino chip.
 
By the end of November 2013 we need to know how much time & money we need to finish the project
 
By the end of November 2013 we need to know how much time & money we need to finish the project
Line 16: Line 25:
 
- Michael
 
- Michael
  
status: driver boards are ready. H-bridge driver, it feeds +24V and -12V to advance one step.  
+
status: driver boards are ready. H-bridge driver, it feeds +24V and -12V to advance one step. <br>
Driver boards tested at 12V. At 12V the driver is not reliable enough to advance the flappers. Boards are 24V compatible.
+
Driver boards tested at 12V. At 12V the driver is not reliable enough to advance the flappers. Boards are 24V compatible.<br>
1 Flapper is 5W. So we can't drive all flappers at once.  
+
1 Flapper is 5W. So we can't drive all flappers at once. <br>
Driver boards are on an SPI bus. These are connected to a Netduino. Merlijn wrote code & GUI to control the Netduino.  
+
Driver boards are on an SPI bus. These are connected to a Netduino. Merlijn wrote code & GUI to control the Netduino. <br>
Flappers have steppermotors. 1 step moves 1 flap.  Unknown begin position of the flappers. You can't check their position.  
+
Flappers have steppermotors. 1 step moves 1 flap.  Unknown begin position of the flappers. You can't check their position.<br>
There's some wear on the flappers. It's not certain if we need the position checker to make it reliable. Possible solution is a webcam with OCR to check the position of the flappers. We have to check this with the customer.
+
There's some wear on the flappers. It's not certain if we need the position checker to make it reliable. Possible solution is a webcam with OCR to check the position of the flappers. We have to check this with the customer.<br>
Wiring all the zero sensors is a lot of work; its uncertain wether they work anymore.  160x 4 wires = a lot.  
+
Wiring all the zero sensors is a lot of work; its uncertain wether they work anymore.  160x 4 wires = a lot. <br>
Driver boards are only with SPI expanders.
+
Driver boards are only with SPI expanders.<br>
 +
We need to run a statistical test, let them change steps for a few hours. See if all flappers end at the same position. If we get the statistical correctness, we can expolate this to 160 flappers, to see the possibility of errors. <br>
 +
The board has a zero sensor and a chip on it. This seems to be a hall sensor at first sight. Somebody needs to research how this chip (anyone has the writings on it?) works, and if there's an easy way to interface it. <br><br>
 +
 
 +
TO DO:<br>
 +
- figure out zero position thing<br>
 +
- find somebody to OCR the flappers.  contact customer if placing a webcam is physically possible<br>
 +
- check how many flappers we have, and how many function properly <br>
 +
- figure out how to display numbers. there's probably flappers that can only show numbers <br>
 +
<br><br>
 +
customer info: Use-IT VZW. Promotes alternative

Latest revision as of 20:46, 30 January 2014


Splitflaps
WhitespaceLogo.gif
What:
twitter feed gets displayed on 4x40 splitflaps
Participants:
Merlijn.

Thijs"Merlijn. Thijs" cannot be used as a page name in this wiki., Bert C, Michael


Cornify

STOCK SUBPAGE http://www.0x20.be/Splitflaps/stock

https://github.com/galgalesh/Splitflaps http://splitflaps.wordpress.com/

http://www.0x20.be/Project_Flappers

Microcontroller: Netduino chip. By the end of November 2013 we need to know how much time & money we need to finish the project

People involved: - Merlijn. created the circuit boards and programmed a part


People to work on the project: - Thijs - Bert - Michael

status: driver boards are ready. H-bridge driver, it feeds +24V and -12V to advance one step.
Driver boards tested at 12V. At 12V the driver is not reliable enough to advance the flappers. Boards are 24V compatible.
1 Flapper is 5W. So we can't drive all flappers at once.
Driver boards are on an SPI bus. These are connected to a Netduino. Merlijn wrote code & GUI to control the Netduino.
Flappers have steppermotors. 1 step moves 1 flap. Unknown begin position of the flappers. You can't check their position.
There's some wear on the flappers. It's not certain if we need the position checker to make it reliable. Possible solution is a webcam with OCR to check the position of the flappers. We have to check this with the customer.
Wiring all the zero sensors is a lot of work; its uncertain wether they work anymore. 160x 4 wires = a lot.
Driver boards are only with SPI expanders.
We need to run a statistical test, let them change steps for a few hours. See if all flappers end at the same position. If we get the statistical correctness, we can expolate this to 160 flappers, to see the possibility of errors.
The board has a zero sensor and a chip on it. This seems to be a hall sensor at first sight. Somebody needs to research how this chip (anyone has the writings on it?) works, and if there's an easy way to interface it.

TO DO:
- figure out zero position thing
- find somebody to OCR the flappers. contact customer if placing a webcam is physically possible
- check how many flappers we have, and how many function properly
- figure out how to display numbers. there's probably flappers that can only show numbers


customer info: Use-IT VZW. Promotes alternative